elevator car
英 [ˈelɪveɪtə(r) kɑː(r)]
美 [ˈelɪveɪtər kɑːr]
网络 电梯轿厢; 轿厢; 电梯车厢
英英释义
noun
- where passengers ride up and down
- the car was on the top floor
双语例句
- An elevator car controller based on CAN bus is described. The functions, architecture, hardware and software and the communication protocol designing methods of this controller are introduced.
简述了一种基于CAN总线的电梯轿厢控制器，介绍了该控制器的功能、结构及其软硬件和通信协议的设计方法。 - Officials say the child's leg was lodged between the elevator car and shaft, with the child's body hanging below the elevator car.
官方称小孩的腿夹在机井和电梯厢中间，身体在电梯厢以下。 - For optimization efficiency of the elevator, the elevator car occupancy percentage is an important data. Existing weight measure system can only measure the weight in the elevator car and can not identify the occupancy percentage.
对于电梯效率最优化而言，轿厢空间被占用面积是一个关键数据，但现有的电梯称重装置只能检测出轿厢中的重量，无法识别轿厢空间占用率。 - The vibration equations of elevator car and guide rail was established, and the relations of variables such as displacement, velocity and excitation force between guide rollers and rails were given by satisfying the geometry compatibility and force equilibrium condition.
分别建立轿厢与导轨振动分析数学模型，基于两者几何相容性与作用力平衡条件，给出导轨与导轮位移、速度、激振力耦合关系。 - Vibration acceleration response of the elevator car is used as feedback signal and thus the engineering implementation of the active control will be simplified.
采用电梯矫厢的振动加速度作为反馈信号，将使主动控制在工程上易于实现。 - It analyzes a hydraulic elevator car frame used in the museum, sets up its multi-loops structure and variable working conditions load.
某博物馆液压电梯轿厢架具有多重框架的结构特点和变工况的载荷特征，传统公式计算法难于进行应力和变形分析。 - Using numerical methods, adopt matlab programming, and obtain the elevator car vibration displacement, velocity and acceleration of the dynamic response simulation curve.
运用数值计算方法，采用matlab仿真，得出电梯轿厢振动位移、速度、加速度的仿真曲线。 - There exist problems of longer design cycle and lower efficiency with common mechanical product design method. In response to it, this paper presents and illustrates a CAD method based on modular and parameterized design, with the aid of elevator car design.
针对传统机械设计方法设计周期长、产品形式单一的问题，本文以电梯轿厢结构设计系统为例提出了基于模块化和参数化设计的机械产品CAD方法。 - The light turns on as soon as the elevator car is activated, such as when the elevator doors open.
电梯启动像电梯开门这种情况下，灯会立即开启。 - This paper establishes the model of the transmission system of the PQS-3-D Elevator for Car with the traditional approach of modeling and analyzes the model in vertical direction to meet the needs of market and design.
本论文就是在这种形势下，响应市场的需求和设计的需要，对PQS-3-D型汽车专用升降机的机械传动系统，采用动力学理论建模方法，进行垂直方向上的建模及分析。